Remove trapped hair from the dry brush bar ID: v8-brush-bar-clean Version: 2.0.0 Model: Dyson V8 SV10 · pinch filter · US Region: US Parts: Pinch-handle Filter A and twist-off Filter B; original dry motorized head Not covered: V8 star pre-filter; V8 Cyclone; Soft roller / Fluffy head cleaning; V10 / V11; Modified batteries or aftermarket heads MATCH YOUR VERSION Top filter: SV10 with the pinch-handle Filter A The V8 name alone does not identify the filter. Compare the label and the official star/pinch selector. Floor head: Original dry motorized head shown in manual 229602-01 This collection covers the original dry head. A washable roller does not make a motorized head washable. Regional instructions: My SV10 label and US manual 229602-01 match Use your supplied regional manual if it differs; do not infer compatibility from a similar name. PREPARE [ ] Read SV10 on the label, confirm the US 229602-01 manual and match the pinch-handle Filter A, twist-off Filter B and any head involved. [ ] Disconnect the charger, release the trigger and let the machine cool before handling removable parts. Keep your hand away from the trigger. [ ] Tool: Good lighting [ ] Tool: Coin for the padlock fastener [ ] Material: Waste bag STOP Stop for a damaged charger, burning smell, liquid exposure, a swollen or leaking battery, broken catches or an obstruction you cannot safely reach. Contact Dyson and keep the battery sealed. CONSUMABLE FIT Coin for the marked fastener: Use only the padlock-marked user brush-bar fastener pictured in the manual. Fit: Matching original dry motorized head Do not substitute: Fluffy/soft roller, unfamiliar fasteners and motor casing screws Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation CHECK ROUTE safety: Is the charger disconnected, the machine cool and undamaged, and your hand away from the trigger? Yes -> check-1: Continue with the matching parts and the checks below. No -> service: Stop for a damaged charger, burning smell, liquid exposure, a swollen or leaking battery, broken catches or an obstruction you cannot safely reach. Contact Dyson and keep the battery sealed. Not sure -> prepared: Save your observations and compare the matching manual before continuing. check-1: Is this the dry motorized head with the padlock-marked coin fastener and removable bar pictured in the manual? Yes -> check-2: Use only that user brush-bar release. No -> prepared: Fluffy, soft roller, newer heads and different fasteners require their own manual. Not sure -> prepared: Save your observations and compare the matching manual before continuing. check-2: Is trapped dry hair/debris visible, with an intact bar and fastener? Yes -> steps: Detach the head before using the coin. No -> prepared: If there is no trapped debris, use the non-turning-brush check; damage needs Dyson support. Not sure -> prepared: Save your observations and compare the matching manual before continuing. CARE STEPS (only when the route reaches steps) [ ] 1. Separate the head With the machine stopped, cool and disconnected from its charger, detach the head from the wand. Place it so the marked fastener and bar end are visible. Look for: The head is disconnected before any brush contact. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 2. Unlock only the marked fastener Use a coin to release the fastener marked with a padlock, following the illustration for this head. Stop if it does not release normally. Look for: The coin engages a user brush-bar lock, not a motor casing screw. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 3. Withdraw the brush bar Slide the released brush bar out in the direction shown for the matching head. Keep the fastener and bar together; stop if parts bind. Look for: The head housing stays closed and dry. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 4. Remove the obstruction dry Carefully remove trapped hair and debris without damaging the bristles. Carbon-fiber brushes may irritate skin; wash your hands after handling them. Keep water and cleaning products away from the motorized head. Look for: The bar and its accessible seating area are free of the observed obstruction. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 5. Return the bar Replace the bar in its original seating position. Ensure it sits correctly before tightening the marked fastener. Look for: A bar that will not seat normally needs the matching manual or support; do not force it. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 6. Secure the fastener Tighten the padlock-marked fastener as shown and check that the bar is held firmly. Reconnect the head only after this check. Look for: The lock is secure before the head is powered again. Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation [ ] 7. Use the assembly check Follow Verify the vacuum after care for bin, filter and connection checks, then observe brush operation during normal use. Stop if it still jams or does not turn. Look for: Save the trapped-material and locking record for any follow-up. Source: dyson-v8-manual, p11 Vacuuming; Washing the filters; p12 Looking for blockages OBSERVATIONS Head confirmed (required): ____________________ Choices: Original dry head with matching padlock fastener Material removed (required): ____________________ Choices: Hair / Thread or fibers / Other accessible dry debris Brush bar is correctly seated and firmly secured by its marked fastener (required): ____________________ RESULT CHECKS [ ] The visible obstruction is removed without opening or wetting the head housing. [ ] The bar is seated and firmly secured before the head is reconnected. NEXT CARE Visible hair or dry debris is trapped around the matching brush bar. As needed for this condition. No fixed calendar interval is specified for this check; choose your own review date if useful. Basis: user-plan Source: dyson-v8-manual, p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation Record preparation, maintenance readiness, problem located or service needed. This is not proof of a physical repair. SOURCES Dyson V8 SV10 operating manual, pinch filter (229602-01) https://www.dyson.com/content/dam/dyson/maintenance/user-guides/en_US/vacuumcleaners/cordlessstickvacuums/sv10/without-soft-roller/229602-01.pdf p12 Looking for blockages; p10 Direct drive cleaner head: Clearing obstructions; p11 Operation Checked: 2026-10-13 Manufacturer copyright. Facts paraphrased; manual and diagrams not redistributed. Choose your Dyson V8 support: star or pinch filter https://www.dyson.com/support/vacuum-cleaners/cordless/v8 V8 support selector: pinch handle versus star filter Checked: 2026-10-13 Linked only; original identification explanation.